845-2019 - Supply and Installation of Security Components for 552 Plinguet and 598 Plinguet

The Work to be done under the Contract shall consist of procure, install and warranty:
Commend intercom system, Genetec Synergis card access components. These components,
with the exception of the Commend Intercom System, will be integrated into the current
Genetec V.5.7 system which includes License Plate Recognition cameras used as access
credentials.
D2.2 The major components of the Work are as follows:
(a) Removal of Steamvault Genetec Network Video Record, Cisco 2960 POE switch, Patch
Panel, APC UPS and reinstall into the 48U open rack located beside the current equipment
rack.
(i) All cables shall be labeled and have cable strain relief boots.
(b) Installation of Commend Intercom Station (552 Plinguet Administration desk, 598 Plinguet
Stores, 552 Plinguet Stores, and 552 Plinguet Emergency Dispatch):
(i) Install and program four (4) Commend (C-EE980) control desk and four (4) (CEEDK9);
(ii) Connect Emergency Dispatch and Administration Desk Commend control desk (CEE980)
to Cisco WS-C2960X-24PD-L through Cat6 cable in server room.
(iii) Connect 598 Stores Commend Control Desk (C-EE980) to Cisco WS-C2960X-
24PD-L through Cat6 cable in stores network area.
(iv) Connect 552 Stores Commend Control Desk (C-EE980) to Cisco WS-C2960X-
24PD-L through Cat6 cable in Utility closet network rack.
(c) Installation of Commend Intercom Station, and R90 long range readers (552 gate access)
(i) Gate ingress: install and program two (2) C-WS311VCM Vandal resistant wall
mount station, two (2) C-WSSH50VSS, surface mount kit, two (2) C-EB3E2A-AUD
expansion mount kit and two (2) C-EB3E2A-AUD WS rainproof hoods on pole
mount supplied. One station mounted high, the other low.
(ii) Connect the two (2) Wall mount stations via Cat6 direct burial via PVC conduit to
one (1) Cisco WS-C2960X-24PD-L (supplied by the City of Winnipeg) located in the
electrical room at 598 Plinguet.
(iii) Install and program three (3) Genetec LP1501 controller cards to Life Safety
Container installed in 598 Plinguet electrical room.
(iv) Install and program nine (9) Genetec SY-S-IR reader licenses to Genetec SV-Pro
network video recorder in 552 Plinguet server room.
(v) Install two (2) R90 HID iCLASS SE long range readers. Adjacent to the intercom
station. Connect to Genetec LP1501 using 22 gauge wire through PVC conduit.
(vi) Install one (1) RP40 HID iCLASS reader and one (1) Interlogix 1045TGY outdoor
sensor on man door to Genetec LP1501 through 22 gauge in EMT conduit.
(vii) Connect current gate sensor to Genetec LP1501.
(viii) Decommission entry keypad.
(ix) Gate egress: install two (2) C-WS311VCM Vandal resistant wall mount station, two
(2) C-WSSH50VSS, surface mount kit, two (2) C-EB3E2A-AUD expansion mount kit
and two (2) C-EB3E2A-AUD WS rainproof hoods on pole mount supplied.
(x) Connect the two (2) Wall mount stations via Cat6 direct burial via EMT conduit to
one (1) Cisco WS-C2960X-24PD-L (supplied by the City of Winnipeg) located in the
electrical room at 598 Plinguet.
(xi) Install two (2) R90 HID iCLASS SE long range readers. Adjacent to the intercom
station. Connect to Genetec 1501 using 22 gauge wire through PVC conduit.
(d) Install and program of Commend Intercom Station and long range readers (598 gate
access)
(i) Install one (1) Omni mount RE12 W in 598 equipment shed (location to be
determined at site visit). Mount one power outlet inside the RE12W. Run power to
the outlet from the breaker panel in the same building.
(ii) Install life safety FLEXPOWER FPO150-C8D8E2 in 598 Equipment Shed. Run
power to unit from breaker panel in the same building.
(iii) Install and program two (2) Genetec LP1501 controller cards in FPO150-C8D8E2
and test connection.
(iv) Run CAT6 direct burial cable from 8 PORT POE+ Cisco in NEMA 4 container
mounted on 598 Plinguet gate bar to the Cisco WS-C2960X-24D-L in the Omni
mount RE12 in the equipment shed. Test connection to Genetec Server.
(v) Gate Ingress: Install and program two (2) Wall mount stations via Cat6 direct burial
via PVC conduit to one (1) Cisco WS-C2960X-24PD-L (supplied by the City of
Winnipeg) mounted in the Omni mount RE 12W.
(vi) Install two (2) R90 HID iCLASS SE long range readers. Adjacent to the intercom
station. Connect to Genetec LP1501 with 22 gauge wire.
(vii) Connect current gate sensor to Genetec LP1501.
(viii) Gate Egress: Install and program two (2) Wall mount stations via Cat6 direct burial
via PVC conduit to one (1) Cisco WS-C2960X-24PD-L (supplied by the City of
Winnipeg) mounted in the Omni mount RE 12W.
(ix) Install two (2) R90 HID iCLASS SE long range readers. Adjacent to the intercom
station. Connect to Genetec LP1501 with 22 gauge wire.
(x) Connect gate sensors to Genetec LP1501
(xi) Decommission entry keypad.
(e) Install, program and configure DELL NX3240 8x10TB drives for 60TB in Raid 6 beneath
the Genetec SV PRO NVR and connect via Ethernet as a NAS to Genetec SVP-PRO in
the 552 Plinguet Server room.
D2.3 The City shall:
(a) Install and program the required POE switches and test the network to ensure
connectivity and assume responsibility for the point to point wireless and fiber optic
network.
(b) Provide the contractor with IP addresses, etc., and information regarding VLAN
configurations.
(c) Provide the contractor with available as-built and vehicle gate installation information.
D2.4 The Contractor shall:
(a) Provide MAC addresses for each network appliance.
(b) Provide As-Built drawings for all infrastructures pertaining to this installation.
D2.5 The major components of the Work are as follows:
(a) Check and identify EMT and PVC conduit for cable spacing.